LME Products

Grid List

10
Set Descending Direction

Items 1 to 10 of 11 total

10 per page
  1. 1
  2. 2
  1. 24x Billet Reluctor Wheel

    24x Billet Reluctor Wheel

    $199.00

    The LME billet 24x reluctor wheel is a direct replacemant of the factory GM two-piece wheel found in 1997-2006 LS series engines. The rigid one piece design improves accuracy and reliabilty as opposed to the stamped and riveted OEM part.The LME reluctor installs using the same alignment tool used for the factory wheel. Due to the one piece design, installation is much easier and consistent, with reluctor run-out well below factory tolerance. Billet 24X wheels also maintain the factory out of balance so rebalancing isn’t required when switching from OEM to the billet wheel

  2. Cam Spec

    Cam Spec

    $35.00

    Fill out the following information to have a cam spec recommended to your exact needs. Pricing of cam spec is applied to purchase of cam.

  3. NEW
    LME Billet Intake LS3

    LME Billet Intake LS3

    $4,495.00

    LME LS3 billet intake manifold offers a large plenum to feed your forced induction mill as well as larger cubic inch naturally aspirated and nitrous engines. Its rigid construction will handle any and all levels of boost without compromise of structural integrity (will not leak or balloon under high boost).

    • Fits under the factory hood of ALL Corvettes including the C6 Z06 without modification.
    • Performance gains over a FAST intake is 30-40 HP and nearly 2000 RPM. When configured with dual throttle bodies, LME’s billet intake is up 75 HP compared to the FAST intake when tested on 480" naturally aspirated engine.
    • Integrated dual nitrous bungs.
    • Accepts single throttle body , factory 90mm LS7 or after market 102mm throttle body.
    • Option for dual injectors allows for use of dual fuel types or the ability to deliver high volumes of fuel

    intakes

  4. NEW
    LME Billet Intake LS7

    LME Billet Intake LS7

    $4,495.00

    LME LS7 billet intake manifold offers a large plenum to feed your forced induction mill as well as larger cubic inch naturally aspirated and nitrous engines. Its rigid construction will handle any and all levels of boost without compromise of structural integrity (will not leak or balloon under high boost).

    • Fits under the factory hood of ALL Corvettes including the C6 Z06 without modification.
    • Performance gains over a FAST intake is 30-40 HP and nearly 2000 RPM. When configured with dual throttle bodies, LME’s billet intake is up 75 HP compared to the FAST intake when tested on 480" naturally aspirated engine.
    • Integrated dual nitrous bungs.
    • Accepts single throttle body , factory 90mm LS7 or after market 102mm throttle body.
    • Option for dual injectors allows for use of dual fuel types or the ability to deliver high volumes of fuel

    intakes

  5. NEW
    LME Billet Intake LT1/LT4

    LME Billet Intake LT1/LT4

    $4,495.00

    LME LT1 billet intake manifold offers a large plenum to feed your forced induction as well as larger cubic inch naturally aspirated and nitrous engines. Its rigid construction will handle any and all levels of boost without compromise of structural integrity (will not leak or balloon under high boost).

    • Fits under the hood of C7 & C7 Z07 without modification.
    • Direct bolt on to LT1 & LT4 cylinder heads
    • Performance gains over GM factory intake is 50 HP and nearly 2000 RPM
    • Integrated dual nitrous bungs.
    • Accepts single throttle body , factory 90mm LT1 or after market 102mm throttle body

    LT1 has provisions for conventional secondary injector . This may be desirable when exceeding the capabilities of factory direct injection fuel system.

  6. NEW
    LME Billet LT1/ LT4 VVT Delete Front Cover

    LME Billet LT1/ LT4 VVT Delete Front Cover

    $495.00
    LME Billet front cover allows you to delete of the factory cam phaser that is know to fluctuate at high RPM and high boost levels. This will improve performance and reliability.
  7. LME Corvette Tee

    LME Corvette Tee

    $20.00

    This shirt makes you look fast even while standing still. As a result this shirt may cause unintentional lifestyle changes such unwarrented tickets or violations from spiteful officers of the law. Caution is advised.

  8. LME Engine Sketch Tee

    LME Engine Sketch Tee

    $20.00

    There have been claims that this shirt has been the unequivocal reason for giving individuals the ability to run faster, jump higher, dance longer, and even eating two nachos at once. We may never know. We are positive, however, that no matter what task you are tackeling while wearing this insatiable garment you will look really really delicious doing it. 

  9. LME Juggernaut LSX Block

    LME Juggernaut LSX Block

    $3,495.00

    Each block is straight from GM and then line-honed with ARP studs before being fitted into one of our Haas CNC machining centers. The block is then bored and decked perfectly true to 90o crank center line before additional machinework is employed. This ensures best proper geometry and provides the most stable platform to host 50+ pounds of boost and 3000+ Horsepower.

    Decide your bore size and other machining operations, we will then sculpt and finish the block to your exact needs. This allows Shop Professionals/Engine Builders a true bespoke precision CNC machined block with a fast turn around. 

  10. LS Billet Valve Covers

    LS Billet Valve Covers

    $849.00
    Will fit all in-line LS cylinder heads

Grid List

10
Set Descending Direction

Items 1 to 10 of 11 total

10 per page
  1. 1
  2. 2

Shop our trusted Brands

  • latemodel
  • callies
  • lsx
  • wiseco
  • dart

Please wait...